Spacecraft propulsion is any method used to accelerate spacecraft and artificial satellites. There are many different methods. Each method has drawbacks and advantages, and spacecraft propulsion is an active area of research. However, most spacecraft today are propelled by forcing a gas from the back/rear of the vehicle at very high speed through a supersonic de Laval nozzle. This sort of engine is called a rocket engine.
All current spacecraft use chemical rockets (bipropellant or solid-fuel) for launch, though some (such as the Pegasus rocket and SpaceShipOne) have used air-breathing engines on their first stage. Most satellites have simple reliable chemical thrusters (often monopropellant rockets) or resistojet rockets for orbital station-keeping and some use momentum wheels for attitude control. Soviet bloc satellites have used electric propulsion for decades, and newer Western geo-orbiting spacecraft are starting to use them for north-south stationkeeping and orbit raising. Interplanetary vehicles mostly use chemical rockets as well, although a few have used ion thrusters and Hall effect thrusters (two different types of electric propulsion) to great success.
- 1 Requirements
- 2 Effectiveness
- 3 Methods
- 4 Planetary and atmospheric propulsion
- 5 Hypothetical methods
- 6 Table of methods
- 7 Testing
- 8 See also
- 9 Notes
- 10 References
- 11 External links
Artificial satellites must be launched into orbit and once there they must be placed in their nominal orbit. Once in the desired orbit, they often need some form of attitude control so that they are correctly pointed with respect to the Earth, the Sun, and possibly some astronomical object of interest.1 They are also subject to drag from the thin atmosphere, so that to stay in orbit for a long period of time some form of propulsion is occasionally necessary to make small corrections (orbital stationkeeping).2 Many satellites need to be moved from one orbit to another from time to time, and this also requires propulsion.3 A satellite's useful life is over once it has exhausted its ability to adjust its orbit.
Spacecraft designed to travel further also need propulsion methods. They need to be launched out of the Earth's atmosphere just as satellites do. Once there, they need to leave orbit and move around.
For interplanetary travel, a spacecraft must use its engines to leave Earth orbit. Once it has done so, it must somehow make its way to its destination. Current interplanetary spacecraft do this with a series of short-term trajectory adjustments.4 In between these adjustments, the spacecraft simply falls freely along its trajectory. The most fuel-efficient means to move from one circular orbit to another is with a Hohmann transfer orbit: the spacecraft begins in a roughly circular orbit around the Sun. A short period of thrust in the direction of motion accelerates or decelerates the spacecraft into an elliptical orbit around the Sun which is tangential to its previous orbit and also to the orbit of its destination. The spacecraft falls freely along this elliptical orbit until it reaches its destination, where another short period of thrust accelerates or decelerates it to match the orbit of its destination.5 Special methods such as aerobraking or aerocapture are sometimes used for this final orbital adjustment.6
Some spacecraft propulsion methods such as solar sails provide very low but inexhaustible thrust;7 an interplanetary vehicle using one of these methods would follow a rather different trajectory, either constantly thrusting against its direction of motion in order to decrease its distance from the Sun or constantly thrusting along its direction of motion to increase its distance from the Sun. The concept has been successfully tested by the Japanese IKAROS solar sail spacecraft.
Spacecraft for interstellar travel also need propulsion methods. No such spacecraft has yet been built, but many designs have been discussed. Since interstellar distances are very great, a tremendous velocity is needed to get a spacecraft to its destination in a reasonable amount of time. Acquiring such a velocity on launch and getting rid of it on arrival will be a formidable challenge for spacecraft designers.8
When in space, the purpose of a propulsion system is to change the velocity, or v, of a spacecraft. Because this is more difficult for more massive spacecraft, designers generally discuss momentum, mv. The amount of change in momentum is called impulse.9 So the goal of a propulsion method in space is to create an impulse.
When launching a spacecraft from the Earth, a propulsion method must overcome a higher gravitational pull to provide a positive net acceleration.10 In orbit, any additional impulse, even very tiny, will result in a change in the orbit path.
The rate of change of velocity is called acceleration, and the rate of change of momentum is called force. To reach a given velocity, one can apply a small acceleration over a long period of time, or one can apply a large acceleration over a short time. Similarly, one can achieve a given impulse with a large force over a short time or a small force over a long time. This means that for maneuvering in space, a propulsion method that produces tiny accelerations but runs for a long time can produce the same impulse as a propulsion method that produces large accelerations for a short time. When launching from a planet, tiny accelerations cannot overcome the planet's gravitational pull and so cannot be used.
The Earth's surface is situated fairly deep in a gravity well. The escape velocity required to get out of it is 11.2 kilometers/second. As human beings evolved in a gravitational field of 1g (9.8 m/s²), an ideal propulsion system would be one that provides a continuous acceleration of 1g (though human bodies can tolerate much larger accelerations over short periods). The occupants of a rocket or spaceship having such a propulsion system would be free from all the ill effects of free fall, such as nausea, muscular weakness, reduced sense of taste, or leaching of calcium from their bones.
The law of conservation of momentum means that in order for a propulsion method to change the momentum of a space craft it must change the momentum of something else as well. A few designs take advantage of things like magnetic fields or light pressure in order to change the spacecraft's momentum, but in free space the rocket must bring along some mass to accelerate away in order to push itself forward. Such mass is called reaction mass.
In order for a rocket to work, it needs two things: reaction mass and energy. The impulse provided by launching a particle of reaction mass having mass m at velocity v is mv. But this particle has kinetic energy mv²/2, which must come from somewhere. In a conventional solid, liquid, or hybrid rocket, the fuel is burned, providing the energy, and the reaction products are allowed to flow out the back, providing the reaction mass. In an ion thruster, electricity is used to accelerate ions out the back. Here some other source must provide the electrical energy (perhaps a solar panel or a nuclear reactor), whereas the ions provide the reaction mass.10
When discussing the efficiency of a propulsion system, designers often focus on effectively using the reaction mass. Reaction mass must be carried along with the rocket and is irretrievably consumed when used. One way of measuring the amount of impulse that can be obtained from a fixed amount of reaction mass is the specific impulse, the impulse per unit weight-on-Earth (typically designated by ). The unit for this value is seconds. Because the weight on Earth of the reaction mass is often unimportant when discussing vehicles in space, specific impulse can also be discussed in terms of impulse per unit mass. This alternate form of specific impulse uses the same units as velocity (e.g. m/s), and in fact it is equal to the effective exhaust velocity of the engine (typically designated ). Confusingly, both values are sometimes called specific impulse. The two values differ by a factor of gn, the standard acceleration due to gravity 9.80665 m/s² ().
A rocket with a high exhaust velocity can achieve the same impulse with less reaction mass. However, the energy required for that impulse is proportional to the exhaust velocity, so that more mass-efficient engines require much more energy, and are typically less energy efficient. This is a problem if the engine is to provide a large amount of thrust. To generate a large amount of impulse per second, it must use a large amount of energy per second. So high-mass-efficient engines require enormous amounts of energy per second to produce high thrusts. As a result, most high-mass-efficient engine designs also provide lower thrust due to the unavailability of high amounts of energy.
Propulsion methods can be classified based on their means of accelerating the reaction mass. There are also some special methods for launches, planetary arrivals, and landings.
A reaction engine is an engine which provides propulsion by expelling reaction mass, in accordance with Newton's third law of motion. This law of motion is most commonly paraphrased as: "For every action force there is an equal, but opposite, reaction force".
Examples include both duct engines and rocket engines, and more uncommon variations such as Hall effect thrusters, ion drives and mass drivers. Duct engines are obviously not used for space propulsion due to the lack of air; however some proposed spacecraft have these kinds of engines to assist takeoff and landing.
Exhausting the entire usable propellant of a spacecraft through the engines in a straight line in free space would produce a net velocity change to the vehicle; this number is termed 'delta-v' ().
If the exhaust velocity is constant then the total of a vehicle can be calculated using the rocket equation, where M is the mass of propellant, P is the mass of the payload (including the rocket structure), and is the velocity of the rocket exhaust. This is known as the Tsiolkovsky rocket equation:
For historical reasons, as discussed above, is sometimes written as
For a high delta-v mission, the majority of the spacecraft's mass needs to be reaction mass. Since a rocket must carry all of its reaction mass, most of the initially-expended reaction mass goes towards accelerating reaction mass rather than payload. If the rocket has a payload of mass P, the spacecraft needs to change its velocity by , and the rocket engine has exhaust velocity ve, then the mass M of reaction mass which is needed can be calculated using the rocket equation and the formula for :
For much smaller than ve, this equation is roughly linear, and little reaction mass is needed. If is comparable to ve, then there needs to be about twice as much fuel as combined payload and structure (which includes engines, fuel tanks, and so on). Beyond this, the growth is exponential; speeds much higher than the exhaust velocity require very high ratios of fuel mass to payload and structural mass.
For a mission, for example, when launching from or landing on a planet, the effects of gravitational attraction and any atmospheric drag must be overcome by using fuel. It is typical to combine the effects of these and other effects into an effective mission delta-v. For example a launch mission to low Earth orbit requires about 9.3–10 km/s delta-v. These mission delta-vs are typically numerically integrated on a computer.
Some effects such as Oberth effect can only be significantly utilised by high thrust engines such as rockets, i.e. engines that can produce a high g-force (thrust per unit mass, equal to delta-v per unit time).
For all reaction engines (such as rockets and ion drives) some energy must go into accelerating the reaction mass. Every engine will waste some energy, but even assuming 100% efficiency, to accelerate an exhaust the engine will need energy amounting to
This energy is not necessarily lost- some of it usually ends up as kinetic energy of the vehicle, and the rest is wasted in residual motion of the exhaust.
Comparing the rocket equation (which shows how much energy ends up in the final vehicle) and the above equation (which shows the total energy required) shows that even with 100% engine efficiency, certainly not all energy supplied ends up in the vehicle - some of it, indeed usually most of it, ends up as kinetic energy of the exhaust.
The exact amount depends on the design of the vehicle, and the mission. However there are some useful fixed points:
- if the is fixed, for a mission delta-v, there is a particular that minimises the overall energy used by the rocket. This comes to an exhaust velocity of about ⅔ of the mission delta-v (see the energy computed from the rocket equation). Drives with a specific impulse that is both high and fixed such as Ion thrusters have exhaust velocities that can be enormously higher than this ideal for many missions.
- if the exhaust velocity can be made to vary so that at each instant it is equal and opposite to the vehicle velocity then the absolute minimum energy usage is achieved. When this is achieved, the exhaust stops in space  and has no kinetic energy; and the propulsive efficiency is 100%- all the energy ends up in the vehicle (in principle such a drive would be 100% efficient, in practice there would be thermal losses from within the drive system and residual heat in the exhaust). However in most cases this uses an impractical quantity of propellant, but is a useful theoretical consideration. Anyway the vehicle has to move before the method can be applied.
Some drives (such as VASIMR or Electrodeless plasma thruster) actually can significantly vary their exhaust velocity. This can help reduce propellant usage or improve acceleration at different stages of the flight. However the best energetic performance and acceleration is still obtained when the exhaust velocity is close to the vehicle speed. Proposed ion and plasma drives usually have exhaust velocities enormously higher than that ideal (in the case of VASIMR the lowest quoted speed is around 15000 m/s compared to a mission delta-v from high Earth orbit to Mars of about 4000m/s).
It might be thought that adding power generation capacity is helpful, and while initially this can improve performance, this inevitably increases the weight of the power source, and eventually the mass of the power source and the associated engines and propellant dominates the weight of the vehicle, and then adding more power gives no significant improvement.
For, although solar power and nuclear power are virtually unlimited sources of energy, the maximum power they can supply is substantially proportional to the mass of the powerplant (i.e. specific power takes a largely constant value which is dependent on the particular powerplant technology). For any given specific power, with a large which is desirable to save propellant mass, it turns out that the maximum acceleration is inversely proportional to . Hence the time to reach a required delta-v is proportional to . Thus the latter should not be too large.
In the ideal case is useful payload and is reaction mass (this corresponds to empty tanks having no mass, etc.). The energy required can simply be computed as
This corresponds to the kinetic energy the expelled reaction mass would have at a speed equal to the exhaust speed. If the reaction mass had to be accelerated from zero speed to the exhaust speed, all energy produced would go into the reaction mass and nothing would be left for kinetic energy gain by the rocket and payload. However, if the rocket already moves and accelerates (the reaction mass is expelled in the direction opposite to the direction in which the rocket moves) less kinetic energy is added to the reaction mass. To see this, if, for example, =10 km/s and the speed of the rocket is 3 km/s, then the speed of a small amount of expended reaction mass changes from 3 km/s forwards to 7 km/s rearwards. Thus, while the energy required is 50 MJ per kg reaction mass, only 20 MJ is used for the increase in speed of the reaction mass. The remaining 30 MJ is the increase of the kinetic energy of the rocket and payload.
Thus the specific energy gain of the rocket in any small time interval is the energy gain of the rocket including the remaining fuel, divided by its mass, where the energy gain is equal to the energy produced by the fuel minus the energy gain of the reaction mass. The larger the speed of the rocket, the smaller the energy gain of the reaction mass; if the rocket speed is more than half of the exhaust speed the reaction mass even loses energy on being expelled, to the benefit of the energy gain of the rocket; the larger the speed of the rocket, the larger the energy loss of the reaction mass.
where is the specific energy of the rocket (potential plus kinetic energy) and is a separate variable, not just the change in . In the case of using the rocket for deceleration, i.e. expelling reaction mass in the direction of the velocity, should be taken negative.
The formula is for the ideal case again, with no energy lost on heat, etc. The latter causes a reduction of thrust, so it is a disadvantage even when the objective is to lose energy (deceleration).
If the energy is produced by the mass itself, as in a chemical rocket, the fuel value has to be , where for the fuel value also the mass of the oxidizer has to be taken into account. A typical value is = 4.5 km/s, corresponding to a fuel value of 10.1 MJ/kg. The actual fuel value is higher, but much of the energy is lost as waste heat in the exhaust that the nozzle was unable to extract.
The required energy is
- for we have
- for a given , the minimum energy is needed if , requiring an energy of
- In the case of acceleration in a fixed direction, and starting from zero speed, and in the absence of other forces, this is 54.4% more than just the final kinetic energy of the payload. In this optimal case the initial mass is 4.92 times the final mass.
These results apply for a fixed exhaust speed.
Due to the Oberth effect and starting from a nonzero speed, the required potential energy needed from the propellant may be less than the increase in energy in the vehicle and payload. This can be the case when the reaction mass has a lower speed after being expelled than before – rockets are able to liberate some or all of the initial kinetic energy of the propellant.
Also, for a given objective such as moving from one orbit to another, the required may depend greatly on the rate at which the engine can produce and maneuvers may even be impossible if that rate is too low. For example, a launch to LEO normally requires a of ca. 9.5 km/s (mostly for the speed to be acquired), but if the engine could produce at a rate of only slightly more than g, it would be a slow launch requiring altogether a very large (think of hovering without making any progress in speed or altitude, it would cost a of 9.8 m/s each second). If the possible rate is only or less, the maneuver can not be carried out at all with this engine.
The power is given by
where is the thrust and the acceleration due to it. Thus the theoretically possible thrust per unit power is 2 divided by the specific impulse in m/s. The thrust efficiency is the actual thrust as percentage of this.
If e.g. solar power is used this restricts ; in the case of a large the possible acceleration is inversely proportional to it, hence the time to reach a required delta-v is proportional to ; with 100% efficiency:
- for we have
- power 1000 W, mass 100 kg, = 5 km/s, = 16 km/s, takes 1.5 months.
- power 1000 W, mass 100 kg, = 5 km/s, = 50 km/s, takes 5 months.
Thus should not be too large.
The power to thrust ratio is simply:11
Thus for any vehicle power P, the thrust that may be provided is:
Suppose we want to send a 10,000 kg space probe to Mars. The required from LEO is approximately 3000 m/s, using a Hohmann transfer orbit. For the sake of argument, let us say that the following thrusters may be used:
|Engine||Effective Exhaust Velocity
|Energy per kg
|minimum power/thrust||Power generator mass/thrust*|
||1||100||190,000||95||500 kJ||0.5 kW/N||N/A|
||5||500||8,200||103||12.6 MJ||2.5 kW/N||N/A|
|Ion thruster||50||5,000||620||775||1.25 GJ||25 kW/N||25 kg/N|
* - assumes a specific power of 1kW/kg
Observe that the more fuel-efficient engines can use far less fuel; its mass is almost negligible (relative to the mass of the payload and the engine itself) for some of the engines. However, note also that these require a large total amount of energy. For Earth launch, engines require a thrust to weight ratio of more than one. To do this with the ion or more theoretical electrical drives, the engine would have to be supplied with one to several gigawatts of power — equivalent to a major metropolitan generating station. From the table it can be seen that this is clearly impractical with current power sources.
Alternative approaches include some forms of laser propulsion, where the reaction mass does not provide the energy required to accelerate it, with the energy instead being provided from an external laser or other beamed power system. Small models of some of these concepts have flown, although the engineering problems are complex and the ground based power systems are not a solved problem.
Instead, a much smaller, less powerful generator may be included which will take much longer to generate the total energy needed. This lower power is only sufficient to accelerate a tiny amount of fuel per second, and would be insufficient for launching from the Earth. However, over long periods in orbit where there is no friction, the velocity will be finally achieved. For example, it took the SMART-1 more than a year to reach the Moon, while with a chemical rocket it takes a few days. Because the ion drive needs much less fuel, the total launched mass is usually lower, which typically results in a lower overall cost, but takes longer.
Mission planning therefore frequently involves adjusting and choosing the propulsion system so as to minimise the total cost of the project, and can involve trading off launch costs and mission duration against payload fraction.
Most rocket engines are internal combustion heat engines (although non combusting forms exist). Rocket engines generally produce a high temperature reaction mass, as a hot gas. This is achieved by combusting a solid, liquid or gaseous fuel with an oxidiser within a combustion chamber. The extremely hot gas is then allowed to escape through a high-expansion ratio nozzle. This bell-shaped nozzle is what gives a rocket engine its characteristic shape. The effect of the nozzle is to dramatically accelerate the mass, converting most of the thermal energy into kinetic energy. Exhaust speed reaching as high as 10 times the speed of sound at sea level are common.
Rocket engines provide essentially the highest specific powers and high specific thrusts of any engine used for spacecraft propulsion.
Ion propulsion rockets can heat a plasma or charged gas inside a magnetic bottle and release it via a magnetic nozzle, so that no solid matter need come in contact with the plasma. Of course, the machinery to do this is complex, but research into nuclear fusion has developed methods, some of which have been proposed to be used in propulsion systems, and some have been tested in a lab.
See rocket engine for a listing of various kinds of rocket engines using different heating methods, including chemical, electrical, solar, and nuclear.
Rather than relying on high temperature and fluid dynamics to accelerate the reaction mass to high speeds, there are a variety of methods that use electrostatic or electromagnetic forces to accelerate the reaction mass directly. Usually the reaction mass is a stream of ions. Such an engine typically uses electric power, first to ionize atoms, and then to create a voltage gradient to accelerate the ions to high exhaust velocities.
For these drives, at the highest exhaust speeds, energetic efficiency and thrust are all inversely proportional to exhaust velocity. Their very high exhaust velocity means they require huge amounts of energy and thus with practical power sources provide low thrust, but use hardly any fuel.
For some missions, particularly reasonably close to the Sun, solar energy may be sufficient, and has very often been used, but for others further out or at higher power, nuclear energy is necessary; engines drawing their power from a nuclear source are called nuclear electric rockets.
With any current source of electrical power, chemical, nuclear or solar, the maximum amount of power that can be generated limits the amount of thrust that can be produced to a small value. Power generation adds significant mass to the spacecraft, and ultimately the weight of the power source limits the performance of the vehicle.
Current nuclear power generators are approximately half the weight of solar panels per watt of energy supplied, at terrestrial distances from the Sun. Chemical power generators are not used due to the far lower total available energy. Beamed power to the spacecraft shows some potential.
Some electromagnetic methods:
- Ion thrusters (accelerate ions first and later neutralize the ion beam with an electron stream emitted from a cathode called a neutralizer)
- Electrothermal thrusters (electromagnetic fields are used to generate a plasma to increase the heat of the bulk propellant, the thermal energy imparted to the propellant gas is then converted into kinetic energy by a nozzle of either physical material construction or by magnetic means)
- Electromagnetic thrusters (ions are accelerated either by the Lorentz Force or by the effect of electromagnetic fields where the electric field is not in the direction of the acceleration)
- Mass drivers (for propulsion)
In electrothermal and electromagnetic thrusters, both ions and electrons are accelerated simultaneously, no neutralizer is required.
The law of conservation of momentum is usually taken to imply that any engine which uses no reaction mass cannot accelerate the center of mass of a spaceship (changing orientation, on the other hand, is possible). But space is not empty, especially space inside the Solar System; there are gravitation fields, magnetic fields, electromagnetic waves, solar wind and solar radiation. Electromagnetic waves in particular are known to contain momentum, despite being massless; specifically the momentum flux density P of an EM wave is quantitatively 1/c times the Poynting vector S, i.e. P = S/c, where c is the velocity of light. Field propulsion methods which do not rely on reaction mass thus must try to take advantage of this fact by coupling to a momentum-bearing field such as an EM wave that exists in the vicinity of the craft. However, since many of these phenomena are diffuse in nature, corresponding propulsion structures need to be proportionately large.
There are several different space drives that need little or no reaction mass to function. A tether propulsion system employs a long cable with a high tensile strength to change a spacecraft's orbit, such as by interaction with a planet's magnetic field or through momentum exchange with another object.13 Solar sails rely on radiation pressure from electromagnetic energy, but they require a large collection surface to function effectively. The magnetic sail deflects charged particles from the solar wind with a magnetic field, thereby imparting momentum to the spacecraft. A variant is the mini-magnetospheric plasma propulsion system, which uses a small cloud of plasma held in a magnetic field to deflect the Sun's charged particles. An E-sail would use very thin and lightweight wires holding an electric charge to deflect these particles, and may have more controllable directionality.
As a proof of concept, NanoSail-D became the first nanosatellite to orbit the Earth.14full citation needed There are plans to add themclarification needed to future Earth orbit satellites, enabling them to de-orbit and burn up once they are no longer needed. Cube sail aims to tackle space junk.15full citation needed
A satellite or other space vehicle is subject to the law of conservation of angular momentum, which constrains a body from a net change in angular velocity. Thus, for a vehicle to change its relative orientation without expending reaction mass, another part of the vehicle may rotate in the opposite direction. Non-conservative external forces, primarily gravitational and atmospheric, can contribute up to several degrees per day to angular momentum,16 so secondary systems are designed to "bleed off" undesired rotational energies built up over time. Accordingly, many spacecraft utilize reaction wheels or control moment gyroscopes to control orientation in space.17
A gravitational slingshot can carry a space probe onward to other destinations without the expense of reaction mass. By harnessing the gravitational energy of other celestial objects, the spacecraft can pick up kinetic energy.18 However, even more energy can be obtained from the gravity assist if rockets are used.
High thrust is of vital importance for Earth launch. Thrust has to be greater than weight (see also gravity drag). Many of the propulsion methods above give a thrust/weight ratio of much less than 1, and so cannot be used for launch.
All current spacecraft use chemical rocket engines (bipropellant or solid-fuel) for launch. Other power sources such as nuclear have been proposed and tested, but safety, environmental and political considerations have so far curtailed their use.
One advantage that spacecraft have in launch is the availability of infrastructure on the ground to assist them. Proposed non-rocket spacelaunch ground-assisted launch mechanisms include:
- Space elevator (a geostationary tether to orbit)
- Launch loop (a very fast enclosed rotating loop about 80 km tall)
- Space fountain (a very tall building held up by a stream of masses fired from base)
- Orbital ring (a ring around the Earth with spokes hanging down off bearings)
- Hypersonic skyhook (a fast spinning orbital tether)
- Electromagnetic catapult (railgun, coilgun) (an electric gun)
- Rocket sled launch
- Space gun (Project HARP, ram accelerator) (a chemically powered gun)
- Beam-powered propulsion rockets and jets powered from ground via a beam
- High-altitude platforms to assist initial stage
- Orbital airship
Studies generally show that conventional air-breathing engines, such as ramjets or turbojets are basically too heavy (have too low a thrust/weight ratio) to give any significant performance improvement when installed on a launch vehicle itself. However, launch vehicles can be air launched from separate lift vehicles (e.g. B-29, Pegasus Rocket and White Knight) which do use such propulsion systems. Jet engines mounted on a launch rail could also be so used.
On the other hand, very lightweight or very high speed engines have been proposed that take advantage of the air during ascent:
- SABRE - a lightweight hydrogen fuelled turbojet with precooler19
- ATREX - a lightweight hydrogen fuelled turbojet with precooler20
- Liquid air cycle engine - a hydrogen fuelled jet engine that liquifies the air before burning it in a rocket engine
- Scramjet - jet engines that use supersonic combustion
Normal rocket launch vehicles fly almost vertically before rolling over at an altitude of some tens of kilometers before burning sideways for orbit; this initial vertical climb wastes propellant but is optimal as it greatly reduces airdrag. Airbreathing engines burn propellant much more efficiently and this would permit a far flatter launch trajectory, the vehicles would typically fly approximately tangentially to the earth surface until leaving the atmosphere then perform a rocket burn to bridge the final delta-v to orbital velocity.
When a vehicle is to enter orbit around its destination planet, or when it is to land, it must adjust its velocity. This can be done using all the methods listed above (provided they can generate a high enough thrust), but there are a few methods that can take advantage of planetary atmospheres and/or surfaces.
- Aerobraking allows a spacecraft to reduce the high point of an elliptical orbit by repeated brushes with the atmosphere at the low point of the orbit. This can save a considerable amount of fuel since it takes much less delta-V to enter an elliptical orbit compared to a low circular orbit. Since the braking is done over the course of many orbits, heating is comparatively minor, and a heat shield is not required. This has been done on several Mars missions such as Mars Global Surveyor, Mars Odyssey and Mars Reconnaissance Orbiter, and at least one Venus mission, Magellan.
- Aerocapture is a much more aggressive manoeuver, converting an incoming hyperbolic orbit to an elliptical orbit in one pass. This requires a heat shield and much trickier navigation, since it must be completed in one pass through the atmosphere, and unlike aerobraking no preview of the atmosphere is possible. If the intent is to remain in orbit, then at least one more propulsive maneuver is required after aerocapture—otherwise the low point of the resulting orbit will remain in the atmosphere, resulting in eventual re-entry. Aerocapture has not yet been tried on a planetary mission, but the re-entry skip by Zond 6 and Zond 7 upon lunar return were aerocapture maneuvers, since they turned a hyperbolic orbit into an elliptical orbit. On these missions, since there was no attempt to raise the perigee after the aerocapture, the resulting orbit still intersected the atmosphere, and re-entry occurred at the next perigee.
- a Ballute is an inflatable drag device
- Parachutes can land a probe on a planet or moon with an atmosphere, usually after the atmosphere has scrubbed off most of the velocity, using a heat shield.
- Airbags can soften the final landing.
- Lithobraking, or stopping by simply smashing into the target, is usually done by accident. However, it may be done deliberately with the probe expected to survive (see, for example, Deep Space 2), in which case very sturdy probes and low approach velocities are required.
A variety of hypothetical propulsion techniques have been considered that would require entirely new principles of physics to be realized or that may not exist. To date, such methods are highly speculative and include:citation needed
- Diametric drive
- Pitch drive & Bias drive
- Disjunction drive
- Alcubierre drive (a form of Warp drive)
- Differential sail
- Wormholes – theoretically possible, but unachieveable in practice with current technology
- Woodward effect
- Reactionless drives – breaks the law of conservation of momentum; theoretically impossible
- EmDrive – tries to circumvent the law of conservation of momentum; may be theoretically impossible
- Photon rocket
- A "hyperspace" drive based upon Heim theory
- Micronewton electromagnetic thruster - Linear momentum loss has been claimed for an electromagnetically powered thruster21
Below is a summary of some of the more popular, proven technologies, followed by increasingly speculative methods.
Four numbers are shown. The first is the effective exhaust velocity: the equivalent speed that the propellant leaves the vehicle. This is not necessarily the most important characteristic of the propulsion method; thrust and power consumption and other factors can be. However:
- if the delta-v is much more than the exhaust velocity, then exorbitant amounts of fuel are necessary (see the section on calculations, above)
- if it is much more than the delta-v, then, proportionally more energy is needed; if the power is limited, as with solar energy, this means that the journey takes a proportionally longer time
The second and third are the typical amounts of thrust and the typical burn times of the method. Outside a gravitational potential small amounts of thrust applied over a long period will give the same effect as large amounts of thrust over a short period. (This result does not apply when the object is significantly influenced by gravity.)
The fourth is the maximum delta-v this technique can give (without staging). For rocket-like propulsion systems this is a function of mass fraction and exhaust velocity. Mass fraction for rocket-like systems is usually limited by propulsion system weight and tankage weight. For a system to achieve this limit, typically the payload may need to be a negligible percentage of the vehicle, and so the practical limit on some systems can be much lower.
|Solid-fuel rocket||minutes||~ 7||9:Flight proven|
|Hybrid rocket||minutes||> 3||9:Flight proven|
|Monopropellant rocket||citation needed1 – 3||citation needed0.1 – 100||milliseconds-minutes||~ 3||9:Flight proven|
|Liquid-fuel rocket||minutes||~ 9||9:Flight proven|
|Electrostatic ion thruster||22full citation needed15 – 210||months/years||> 100||9:Flight proven|
|Hall effect thruster (HET)||citation needed8 - 50||months/years||> 100||239:Flight proven|
|Resistojet rocket||2 - 6||10−2 - 10||minutes||?||248:Flight qualified|
|Arcjet rocket||4 - 16||10−2 - 10||minutes||?||citation needed8:Flight qualified|
|Field Emission Electric Propulsion (FEEP)||25-130100||25-10−32510−6||months/years||?||258:Flight qualified|
|Pulsed plasma thruster (PPT)||~ 20||~ 0.1||~2,000–10,000 hours||?||7:Prototype demoed in space|
|Dual mode propulsion rocket||1 – 4.7||0.1 – 107||milliseconds-minutes||~ 3 – 9||7:Prototype demoed in space|
9/km2 @ 1 |
9:Light pressure attitude-control flight proven|
6:Deploy-only demoed in space
5:Light-sail validated in lit vacuum
|Tripropellant rocket||citation needed2.5 - 5.3||citation needed0.1 - 107||minutes||~ 9||266:Prototype demoed on ground|
|Magnetoplasmadynamic thruster (MPD)||20 - 100||100||weeks||?||276:Model-1 kW demoed in space|
|Nuclear thermal rocket||289||28107||28minutes||> ~ 20||6:Prototype demoed on ground|
|Mass drivers (for propulsion)||0 - ~30||104 - 108||months||?||6:Model-32MJ demoed on ground|
|Tether propulsion||N/A||1 - 1012||minutes||~ 7||296:Model-31.7 km demoed in space|
|Air-augmented rocket||5 - 6||0.1 - 107||seconds-minutes||> 7?||30316:Prototype demoed on ground|
|Liquid air cycle engine||4.5||103 - 107||seconds-minutes||?||6:Prototype demoed on ground|
|Pulsed inductive thruster (PIT)||32-803210||20||months||?||325:Component validated in vacuum|
|Variable Specific Impulse Magnetoplasma Rocket (VASIMR)||citation needed10 - 300||citation needed40 - 1,200||days - months||> 100||5:Component-200 kW validated in vacuum|
|Magnetic field oscillating amplified thruster||10 - 130||0.1 - 1||days - months||> 100||5:Component validated in vacuum|
|Solar thermal rocket||7 - 12||1 - 100||weeks||> ~ 20||334:Component validated in lab|
|Radioisotope rocket||citation needed7 - 8||1.3 - 1.5||months||?||4:Component validated in lab|
|Nuclear electric rocket(As electric prop. method used)||Variable||Variable||Variable||?||400kW validated in lab4:Component-|
|Orion Project (Near term nuclear pulse propulsion)||20 - 100||109 - 1012||several days||~30-60||34353:Validated-900 kg proof-of-concept|
|Space elevator||N/A||N/A||indefinite||> 12||3:Validated proof-of-concept|
|Reaction Engines SABRE19||30/4.5||0.1 - 107||minutes||9.4||3:Validated proof-of-concept|
|Magnetic sails||145-750:Wind||Mg3670/40||indefinite||?||3:Validated proof-of-concept|
|Magnetic sail#Mini-magnetospheric plasma propulsion||200||~1 N/kW||months||?||373:Validated proof-of-concept|
|Beam-powered/Laser(As prop. method powered by beam)||Variable||Variable||Variable||?||3:Validated-71m proof-of-concept|
|Launch loop/Orbital ring||N/A||~104||minutes||>>11-30||Technology concept formulated2:|
|Nuclear pulse propulsion (Project Daedalus' drive)||20 - 1,000||109 - 1012||years||~15,000||2:Technology concept formulated|
|Gas core reactor rocket||10 - 20||103 - 106||?||?||2:Technology concept formulated|
|Nuclear salt-water rocket||100||103 - 107||half hour||?||2:Technology concept formulated|
|Fission sail||?||?||?||?||2:Technology concept formulated|
|Fission-fragment rocket||15,000||?||?||?||2:Technology concept formulated|
|Nuclear photonic rocket||299,790||10−5 - 1||years-decades||?||2:Technology concept formulated|
|Fusion rocket||citation needed100 - 1,000||?||?||?||2:Technology concept formulated|
|Antimatter catalyzed nuclear pulse propulsion||200 - 4,000||?||days-weeks||?||2:Technology concept formulated|
|Antimatter rocket||citation needed10,000-100,000||?||?||?||2:Technology concept formulated|
|Bussard ramjet||2.2 - 20,000||?||indefinite||~30,000||2:Technology concept formulated|
|Gravitoelectromagnetic toroidal launchers||clarification needed299,790:GEM||?||?||citation needed<299790||1:Basic principles observed & reported|
Spacecraft propulsion systems are often first statically tested on the Earth's surface, within the atmosphere but many systems require a vacuum chamber to test fully. Rockets are usually tested at a rocket engine test facility well away from habitation and other buildings for safety reasons. Ion drives are far less dangerous and require much less stringent safety, usually only a large-ish vacuum chamber is needed.
Famous static test locations can be found at Rocket Ground Test Facilities
Some systems cannot be adequately tested on the ground and test launches may be employed at a Rocket Launch Site.
- In-space propulsion technologies
- Interplanetary travel
- Interstellar travel
- List of aerospace engineering topics
- List of rockets
- Magnetic sail
- Orbital maneuver
- Orbital mechanics
- Plasma propulsion engine
- Pulse detonation engine
- Rocket engine nozzles
- Solar sail
- Specific impulse
- Tsiolkovsky rocket equation
- Stochastic electrodynamics
- ^ With things moving around in orbits and nothing staying still, the question may be quite reasonably asked, stationary relative to what? The answer is for the energy to be zero (and in the absence of gravity which complicates the issue somewhat), the exhaust must stop relative to the initial motion of the rocket before the engines were switched on. It is possible to do calculations from other reference frames, but consideration for the kinetic energy of the exhaust and propellant needs to be given. In Newtonian mechanics the initial position of the rocket is the centre of mass frame for the rocket/propellant/exhaust, and has the minimum energy of any frame.
- Hess, M.; Martin, K. K.; Rachul, L. J. (February 7, 2002). "Thrusters Precisely Guide EO-1 Satellite in Space First". NASA. Archived from the original on 2007-12-06. Retrieved 2007-07-30.
- Phillips, Tony (May 30, 2000). "Solar S'Mores". NASA. Retrieved 2007-07-30.
- Olsen, Carrie (September 21, 1995). "Hohmann Transfer & Plane Changes". NASA. Archived from the original on 2007-07-15. Retrieved 2007-07-30.
- Staff (April 24, 2007). "Interplanetary Cruise". 2001 Mars Odyssey. NASA. Retrieved 2007-07-30.dead link
- Doody, Dave (February 7, 2002). "Chapter 4. Interplanetary Trajectories". Basics of Space Flight (NASA JPL). Retrieved 2007-07-30.
- Hoffman, S. (August 20–22, 1984). "A comparison of aerobraking and aerocapture vehicles for interplanetary missions". AIAA and AAS, Astrodynamics Conference. Seattle, Washington: American Institute of Aeronautics and Astronautics. pp. 25 p. Retrieved 2007-07-31.
- Anonymous (2007). "Basic Facts on Cosmos 1 and Solar Sailing". The Planetary Society. Retrieved 2007-07-26.
- Rahls, Chuck (December 7, 2005). "Interstellar Spaceflight: Is It Possible?". Physorg.com. Retrieved 2007-07-31.
- Zobel, Edward A. (2006). "Summary of Introductory Momentum Equations". Zona Land. Retrieved 2007-08-02.
- Benson, Tom. "Guided Tours: Beginner's Guide to Rockets". NASA. Retrieved 2007-08-02.
- equation 19-1 Rocket propulsion elements 7th edition- Sutton
- Choueiri, Edgar Y. (2004). "A Critical History of Electric Propulsion: The First 50 Years (1906–1956)". Journal of Propulsion and Power 20 (2): 193–203. doi:10.2514/1.9245.
- Drachlis, Dave (October 24, 2002). "NASA calls on industry, academia for in-space propulsion innovations". NASA. Retrieved 2007-07-26.
- NASA's Nanosail-D Becomes the First Solar Sail Spacecraft to Orbit the Earth | Inhabitat - Green Design Will Save the World
- Amos, Jonathan (2010-03-26). "Tiny cube will tackle space junk". BBC News.
- King-Hele, Desmond (1987). Satellite orbits in an atmosphere: Theory and application. Springer. ISBN 978-0-216-92252-5.
- P.; Shen, H.; Hall, C. D. (2001). "Satellite attitude control and power tracking with energy/momentum wheels". Journal of Guidance, Control, and Dynamics 43 (1): 23–34. Bibcode:2001JGCD...24...23T. doi:10.2514/2.4705. ISSN 0731-5090.
- Dykla, J. J.; Cacioppo, R.; Gangopadhyaya, A. (2004). "Gravitational slingshot". American Journal of Physics 72 (5): 619–000. Bibcode:2004AmJPh..72..619D. doi:10.1119/1.1621032.
- Anonymous (2006). "The Sabre Engine". Reaction Engines Ltd. Retrieved 2007-07-26.
- Harada, K.; Tanatsugu, N.; Sato, T. (1997). "Development Study on ATREX Engine". Acta Astronautica 41 (12): 851–862. doi:10.1016/S0094-5765(97)00176-8.
- Dimitri S.H. Charrier (2012). "Micronewton electromagnetic thruster". Applied Physics Letters 101. p. 034104.
- ESA Portal – ESA and ANU make space propulsion breakthrough
- Hall effect thrusters have been used on Soviet/Russian satellites for decades.
- A Xenon Resistojet Propulsion System for Microsatellites (Surrey Space Centre, University of Surrey, Guildford, Surrey)
- Alta - Space Propulsion, Systems and Services - Field Emission Electric Propulsion
- Google Translate
- Young Engineers' Satellite 2
- NASA GTX
- The PIT MkV pulsed inductive thruster
- Pratt & Whitney Rocketdyne Wins $2.2 Million Contract Option for Solar Thermal Propulsion Rocket Engine (Press release, June 25, 2008, Pratt & Whitney Rocketdyne)
- "Operation Plumbbob". July 2003. Retrieved 2006-07-31.
- Brownlee, Robert R. (June 2002). "Learning to Contain Underground Nuclear Explosions". Retrieved 2006-07-31.
- PSFC/JA-05-26:Physics and Technology of the Feasibility of Plasma Sails, Journal of Geophysical Research, September 2005
- NASA Beginner's Guide to Propulsion
- NASA Breakthrough Propulsion Physics project
- Rocket Propulsion
- Journal of Advanced Theoretical Propulsion
- Different Rockets
- Earth-to-Orbit Transportation Bibliography
- Spaceflight Propulsion - a detailed survey by Greg Goebel, in the public domain
- Rocket motors on howstuffworks.com
- Johns Hopkins University, Chemical Propulsion Information Analysis Center
- Tool for Liquid Rocket Engine Thermodynamic Analysis
- NASA Jet Propulsion Laboratory
- Smithsonian National Air and Space Museum's How Things Fly website